A Pair Of Firearm-Related Product Recalls

Safety is paramount when dealing with firearms. If either of these recalls effect you, please stop using the product and follow the manufacturer's instructions for returning the product for upgrade or replacement.

First, for the person who assembles their own AR15 comes this from American Outdoor Brand's Battenfield Technologies subsidiary. It is the AR15 lower parts kit (Item #110114) sold prior to September 12, 2017 and marketed under the S&W M&P label. It only applies to the lower parts kit and not to factory assembled S&W M&P-15s. The hammer in the kit is missing a pin due to a packaging error.

Here is a picture of the hammer involved and the steps you need to take to remedy the issue.

Remedy/Action to be Taken

DO NOT ASSEMBLE A RIFLE USING THIS M&P15 COMPLETE LOWER PARTS KIT. IF YOU HAVE ALREADY DONE SO, STOP USING THE RIFLE IMMEDIATELY.

Any unintended discharge of a firearm has the potential to cause injury. We are asking all purchasers of the M&P AR-15 Rifle Lower Parts Kit Complete to refrain from assembling a rifle using the hammer from the kit. If you have already done so, immediately stop using the rifle until corrective action can be taken.

To facilitate this repair, please contact Battenfeld Technologies, Inc. at the number below to arrange for the return and replacement of the M&P AR-15 Rifle Lower Parts Kit Complete, or the hammer only from the kit.

When you return the hammer, we will replace it with a new part at no cost to you. Your hammer will be returned as quickly and efficiently as possible. Remember, while you are awaiting the replacement hammer, any rifle assembled with an M&P AR-15 Rifle Lower Parts Kit Complete should NOT be used. The lower receiver should be disassembled and the rifle should be stored unloaded and with the safety in the SAFE LOAD/UNLOAD position.

Please do NOT return firearms or receivers to Battenfeld Technologies, Inc. Firearms or receivers received by Battenfeld will be returned to sender WITHOUT remedial action. The M&P AR-15 Rifle Lower Parts Kit Complete with the replacement hammer will be identified as Item #1085634.

For hammer-only replacements, you should note a J pin as shown in the photo below. This J pin is confirmation that your hammer has been replaced.

Consumer Contact:

To arrange for the replacement of the hammer, email us at recall110114@btibrands.com or call us at (877) 416-5167. Your hammer will be returned as quickly and efficiently as possible.

IF YOU HAVE ANY QUESTIONS ABOUT THIS RECALL, PLEASE CONTACT BATTENFELD TECHNOLOGIES, INC. AT (877) 416-5167.

The second recall comes from SIG and involves a limited number of their SIG716, SIG516, and SIGM400 rifles which may have an improperly heat-treated hammer in the trigger assembly.

Newington, NH (September 15th, 2017) – SIG SAUER, Inc. has determined that a limited number of rifles in the SIG716 DMR®, SIG516® Carbon Fiber and SIGM400® Predator models were built with a two-stage SIG SAUER trigger that may have an improperly heat-treated hammer. Over time this could result in a trigger malfunction creating a significant safety hazard. SIG SAUER is issuing a mandatory recall to replace the hammer and trigger assembly in these specific rifles. This recall does not affect any military or law enforcement rifles or any SIG MCX®/SIG MPX® products.

SIG SAUER will correct any of the affected firearms at no cost to the customer.

To determine if a specific firearm is affected by the recall, go to https://www.sigsauer.com/support/safety-center/rifle-safety-warning/ and utilize the serial number identifier and visual inspection instructions.

If you are a customer who is affected by the recall, stop using the firearm immediately and follow the instructions on the website or call SIG SAUER Customer Service by dialing 603-610-3000, option #1. Have the rifle’s serial number available.

To reiterate on both recalls, if you own either of the products involved, stop using them now and contact the manufacturers involved.


UPDATE: In an absurd posting, the Bloomberg-financed, anti-gun "news service" (sic) The Trace criticizes SIG over their safety warning and recall. They contend that SIG is "keeping gun owners in the dark" by just saying it can cause a "trigger malfunction" due to the improper heat treatment of the hammer. The Trace wants SIG to go into chapter and verse over what a trigger malfunction might cause. They point to the safety warning (probably mandated by the Consumer Product Safety Commission) issued by Takata on their air bag recall.

I think the average firearm user recognizes that they are a) using a tool that can have deadly consequences if misused, b) that a trigger malfunction is not good, and c) you don't mess around with trigger malfunctions.